ZEROPLAY Miter Bar (1 Bar)
or buy separately
ZEROPLAY
Miter Bar (Single)
Included in the box:
- Miter Bar
Visit our retailers to get it by Christmas!
100% Satisfaction Guaranteed
- Priority Mail Express: No delays.
- Priority Mail: 1-2 day delay. No delays for local delivery.
- First-Class Package Service: 1-2 day delay.
New and improved
Create precise sleds for your table saw, router table and band saw quickly and easily with the ZEROPLAY Miter Bar. You adjust the fit of the ZEROPLAY from above after it is mounted to the sled base, so you can control the exact fit you want; gliding feather-light along your table with zero side-to-side movement. Truly zero play with the ZEROPLAY Miter Bars. Fits any standard 3/4” miter slot.
The defining feature and flaw of aftermarket miter bars are one in the same - set screws. Frustrated with the difficulty of fitting miter bars with set screws, Founder and inventor, Henry Wang, set out to change it. He conceived a method of adjustment based on opposing wedges, that adjusted the entire bar evenly in a single motion. With its ONE-TOUCH CALIBRATION® and top-down installation, the age-old struggles of sled making had finally been solved.
Calibrate your miter bar quickly and accurately from above the sled.
ZeroPlay Miter Bars are adjusted to fit the miter slot while it is attached to your sled, allowing you to get the best fit possible.Just set, test, adjust if needed, then begin using your sled. The two halves of the ZeroPlay expand to fit the slot, providing full contact all along both edges of the bar.
- Fits any standard 3/4" x 3/8” miter slots.
- Mounts and adjusts from above the sled base for fast and accurate set up every time.
- Glass reinforced parts will not warp or swell with environmental changes like wood runners.
Will it fit my miter slot?
Create your own clamp tracks.
With MatchFit, you're not confined to pre-set clamp positions. Carve out your custom dovetail tracks on any wooden surface, enhancing your hold-down capabilities where you need them most. The Dovetail Track System gives you all the functionality of T-track, in less time and at a fraction of the cost.
Seamless dovetail integration: All MatchFit clamps slide into any 1/2" x 14º dovetail groove, transforming your setup into a unified clamping haven for unmatched efficiency.
Top-down installation for hassle free setup.
Mount and adjust from above for the best fit fast.
ZEROPLAY is adjusted to the miter slot while in the miter slot and attached to your sled for the best possible fit with the least possible effort.
Speed and versatility
Miter Bars can be used in tandem for longer sleds or to engage both miter slots at the same time. Retrofit to your existing sled and move easily from jig to jig.
Use it around your whole shop.
Features.
ZEROPLAY Miter Bar (1 Bar)
ZEROPLAY 360 Sled Kit
Frequently Bought Together
MATCHFIT Dovetail Hardware Variety Pack
MATCHFIT Dovetail Hardware Variety Pack
MATCHFIT Dovetail Router Bit (1/2"-14°)
MATCHFIT Dovetail Router Bit (1/2"-14°)
MATCHFIT Dovetail Clamp (2-pack)
MATCHFIT Dovetail Clamp (2-pack)
ZEROPLAY Miter Stop
ZEROPLAY Miter Stop
What people are saying.
Great-fitting guide bar
This kit was perfect for what I needed/wanted.
Amazon best seller.
Very happy with this purchase.
Build a fast accurate compound miter sled
Got questions?
Does the ZEROPLAY Miter Bar work with Shopsmith® miter tracks?
It depends. The miter slots vary in width from model to model. Measure your miter slot to ensure that it is at least .730" wide"
I’m having trouble adjusting my miter bars - either too tight or too loose. Any tips?
If your miter bar fits well but becomes too tight when installed on a sled, you may have tightened the panhead screws too much. Overtightening those screws can cause the bars to compress and expand outward. Try putting a single strip of paper on the inside of one of the miter slots when adjusting the miter bars’ width. This should offset the compression that occurs during installation.
My table saw has tabs at the top of the miter slot. Will ZEROPLAY Miter Bars work on my saw?
No. The tabs will get in the way. Refer to the compatibility diagram here:
Will ZEROPLAY Miter Bars fit my saw?
ZEROPLAY Miter Bars will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0.73" and 0.79" wide and at least 5/16" deep.
Compatible miter tracks include but not exclusive to ShopSmith, SawStop, Bosch 4100, Delta Unisaw, Powermatic, Rigid, Dewalt, and General 350 Tracks.
*Not compatible with table saws with 'Tabs' cast into the top of the miter slot or 5/8" miter slots i.e. Ryobi or Craftsman.
The Most Epic 360 Table Saw Sled
How to Build the Ultimate Table Saw Sled
ZEROPLAY 360 Sled Kit
ZeroPlay ZP750 - Instructional Video
Specifications.
Parts
- Miter Bar
Parts
- (2) Miter Bars
- (2) Miter Stops
Parts
- (1) Miter Bar
- (4) 1.5" Dovetail Track Screws
ZEROPLAY Miter Bars and Stops will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0.73" and 0.79" wide and at least 5/16" deep.
Compatible miter tracks include but not exclusive to: SawStop, Bosch 4100, Delta Unisaw, Powermatic, Rigid, Dewalt, and General 350 Tracks.
(Not compatible with table saws with 'Tabs' cast into the top of the miter slot or 5/8" miter slots i.e. Ryobi or Craftsman)
ZEROPLAY Miter Bars and Stops will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0.73" and 0.79" wide and at least 5/16" deep.
Compatible miter tracks include but not exclusive to: SawStop, Bosch 4100, Delta Unisaw, Powermatic, Rigid, Dewalt, and General 350 Tracks.
(Not compatible with table saws with 'Tabs' cast into the top of the miter slot or 5/8" miter slots i.e. Ryobi or Craftsman)
ZeroPlay Miter Bars and Stops will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0.73" and 0.79" wide and at least 5/16" deep.
Compatible miter tracks include but not exclusive to: SawStop, Bosch 4100, Delta Unisaw, Powermatic, Rigid, Dewalt, and General 350 Tracks.
(Not compatible with table saws with 'Tabs' cast into the top of the miter slot or 5/8" miter slots i.e. Ryobi or Craftsman)
ZP750-B1
ZP750-B2S2
DV-360ZP750B1
Designed in the USA. Made in Taiwan.
Designed in the USA. Made in Taiwan.
Designed in the USA. Made in Taiwan.
Customer Reviews.
Our Story
Family-Owned & Operated
Established 2001.
For beginners and pros alike, Microjig is reimagining an ancient craft and changing the way you work with wood.
Build your projects with more protection, more precision, and more passion. Work safer. Work smarter.
Designed in the USA by Woodworkers
Protecting Users in 37 Countries and Counting
1% Donated toNon-Profits andCharities
It all started in a garage workshop...
Henry was working on an intricate project and was challenged with cutting thin strips on a table saw. His frustration with traditional methods sparked one of the most innovative woodworking tools to come out in decades.
After countless hours and prototypes, the Grr-ripper was born. Henry has continued to innovate, and Microjig now offers multiple unique product lines all over the world.
WOOD Innovate Award
WOOD Innovate Award
Rated 5/5
Rated 4.8/5
Best for Table Saw Safety
#1 Best Overall Push Block
Best High-end Push Block
Best Multifunctional Push Block
Award Winner
Award Winner
Award Winner
Award Winner
Award Winner
Award Winner
Registered Small Business
Minority-Owned Business
Section 889 Certified
Ad Blocker Detected
Please disable ad blocker for full website functionality.
