Blade and Bit Cleaning System
Over 900,000 GRR-RIPPERs sold
For saw blades up to 12" in diameter and router bits with 1/4”, 1/2”, 6mm, 8mm, or 12mm shank sizes.
Recommended By
BLADECLEAN Blade and Bit Cleaning System
BLADECLEAN Blade and Bit Cleaning System
BLADECLEAN Blade and Bit Cleaning System
or buy separately
LIMITED TIME ONLY
BLADECLEAN
Blade and Bit Cleaning System
Included in the box:
- BLADECLEAN cleaning well
- Magnetic handle
- Wire brush
- Al₂O₃ cleaning discs
- Rotary tool mandrel
Visit our retailers to get it by Christmas!
100% Satisfaction Guaranteed
- Priority Mail Express: No delays.
- Priority Mail: 1-2 day delay. No delays for local delivery.
- First-Class Package Service: 1-2 day delay.
All-in-one blade and bit cleaning
The BLADECLEAN Blade and Bit Cleaning System is the quickest, safest, and most enjoyable way to clean your saw blades and router bits. This all-in-one kit is compatible with:
- Saw blades (circular) - up to 12" in diameter.
- Router bits - 1/4”, 1/2”, 6mm, 8mm, and 12mm shank sizes.
Not compatible with shaper cutters.
Clean blades = clean cuts.
Dirty blades and bits put stress on your machine, generate more heat, and are often mistaken as dull. This is when blades are unnecessarily sent off for sharpening while, more often than not, all they need is a quick cleaning.
Less time cleaning, more time building.
Cleaning saw blades can be tedious and time consuming. The BLADECLEAN system shortens the entire job to just a few minutes. Quickly clean an entire side of your saw blade in a single motion, and without harsh chemicals.
The BLADECLEAN features seals to prevent evaporation of the cleaning fluid, but is not water tight. It should be kept upright during use and storage to prevent spilling
Create your own clamp tracks.
With MatchFit, you're not confined to pre-set clamp positions. Carve out your custom dovetail tracks on any wooden surface, enhancing your hold-down capabilities where you need them most. The Dovetail Track System gives you all the functionality of T-track, in less time and at a fraction of the cost.
Seamless dovetail integration: All MatchFit clamps slide into any 1/2" x 14º dovetail groove, transforming your setup into a unified clamping haven for unmatched efficiency.
BLADECLEAN Features
No bare hand contact with cutting edges or chemicals.
The magnetic handle attaches to your saw blade, so your skin doesn't come into contact with harsh chemicals or sharp cutting edges.
Industrial grade aluminium-oxide cleaning pads.
No more wire brushing! The scouring pad is uniquely suited to reach every nook and cranny of your saw blade at once. Clean an entire side of the blade in a single motion.
Clean a variety of router bit sizes at once.
The router bit holder lets you soak and clean up to five bits in record time using the included scouring discs. Compatible with 1/4”, 1/2”, 6mm, 8mm, and 12mm shank sizes.
Use it around your whole shop.
Features.
BLADECLEAN Blade and Bit Cleaning System
Frequently Bought Together
BLADEMATCH Arbor Shims (6-pack)
BLADEMATCH Arbor Shims (6-pack)
MATCHFIT Dovetail Clamp Pro
MATCHFIT Dovetail Clamp Pro
GRR-RIPPER+
GRR-RIPPER+
BLADECLEAN 13in Pad
BLADECLEAN 13in Pad
What people are saying.
Got questions?
What solvent are you using?
Use your preferred cleaner. Can be Simple Green, Fabuloso, Pinesol, or whatever you like. No need for harsh solvents and chemicals.
Will it work with a 12" blade?
Yes, the cleaning well is designed to work with blades from 7" up to 12"
How long will the BLADECLEAN Pad last?
It depends on how often you clean your blades, but our testing shows that the average woodworker will get several hundred cleanings before needing to replace the pad.
How often do you change the cleaning solution?
The dirt from cleaning tends to sink down through the pad, so it does not affect the cleaning process. When the solution is difficult to see through, it should be replaced.
What is the right speed for the aluminum oxide cleaning discs?
8,000 to 10,000 rpm provides the best balance between cleaning speed and disc life.
I’ve finally worn out my aluminum oxide cleaning discs, now what?
Replacement discs are sold in packs of 14, including a new mandrel, and are available here.
Can I clean router bits with bearings?
Yes, but you should remove the bearing before submerging the bit in cleaning solution. Many common household cleaners contain degreaser and can affect the bearing’s performance.
BLADECLEAN Instructions
Specifications.
Parts
- BLADECLEAN cleaning well
- Magnetic handle
- Wire brush
- Al₂O₃ cleaning discs
- Rotary tool mandrel
Parts
Parts
Saw blades up to 12" in diameter.
Router bits with 1/4”, 1/2”, 6mm, 8mm, or 12mm shank sizes.
BC-81012
Designed in USA
Made in Taiwan
Customer Reviews.
Our Story
Family-Owned & Operated
Established 2001.
For beginners and pros alike, Microjig is reimagining an ancient craft and changing the way you work with wood.
Build your projects with more protection, more precision, and more passion. Work safer. Work smarter.
Designed in the USA by Woodworkers
Protecting Users in 37 Countries and Counting
1% Donated toNon-Profits andCharities
It all started in a garage workshop...
Henry was working on an intricate project and was challenged with cutting thin strips on a table saw. His frustration with traditional methods sparked one of the most innovative woodworking tools to come out in decades.
After countless hours and prototypes, the Grr-ripper was born. Henry has continued to innovate, and Microjig now offers multiple unique product lines all over the world.
WOOD Innovate Award
WOOD Innovate Award
Rated 5/5
Rated 4.8/5
Best for Table Saw Safety
#1 Best Overall Push Block
Best High-end Push Block
Best Multifunctional Push Block
Award Winner
Award Winner
